How do you mix interlux InterProtect 2000E?

Mix three parts of 2000E Gray Base or 2002E White Base with one part 2001E Reactor, and allow it to stand mixed for a minimum of twenty minutes for induction time. Mix only what can be used in five hours. 3. Apply coats of InterProtect 2000E as per chart to the right.

How many coats of InterProtect 2000E?

How many coats of InterProtect?

It usually takes four to five coats to apply the proper amount of InterProtect 2000E, but the final dry film thickness is more important than the number of coats. To prevent delamination, all mold release wax and other contamination must be removed prior to the application of InterProtect Epoxies.

How do you use Pettit barrier coat?

Wipe clean of residue and immediately apply one thin coat of Pettit 6455/044 Metal Primer. Let dry 8 hours minimum, 48 hours maximum, and apply three coats* Pettit Protect following application and recoat instructions. coat of 6455/044 Metal Primer and allow to dry eight hours. Apply one coat of Pettit Protect.

What is a barrier coat on a boat?

A barrier coat seals a fiberglass hull, blocking water entry and inhibiting blister formation in underwater gelcoat and fiberglass. If your boat has a fiberglass hull, you MUST protect it with a barrier coat beneath your bottom paint.

Is Micron Extra ablative?

INTERLUX MICRON EXTRA ABLATIVE ANTIFOULING PAINT – Micron Extra uses Micron technology to provide excellent, long lasting antifouling protection against all types of fouling. Micron Extra includes Biolux, to control slime.

How good is epoxy primer?

An epoxy primer is very effective at sealing up bare metal and prevents moisture or corrosion from creeping in. It keeps out oxygen, ensuring that rust or corrosion do not form on the surface. It is non-porous when it cures and does not soak up moisture like most primer sealers.

Is barrier coat necessary?

A barrier coat seals a fiberglass hull, blocking water entry and inhibiting blister formation in underwater gelcoat and fiberglass. If your boat has a fiberglass hull, you MUST protect it with a barrier coat beneath your bottom paint. Water can’t get in to do damage.

What is the difference between self etching primer and epoxy primer?

Self etching primer bonds well to bare metal surfaces and can be top coated in a short period of time. Epoxy primer can be applied in heavy coats which can be guide coated and block sanded to remove small imperfections in the body. Epoxy primer takes longer to dry (cure) before it can be sanded or top coated.

How does Interlux interprotect barrier coat epoxy primer work?

Technically, InterProtect Micro-Plates provide millions of overlapping microscopic plates that create a barrier similar to shingles on a roof. These overlapping Micro-Plates eliminate any direct path for water migration and also improve the sag resistance of the epoxy making application easier.

What causes osmosis on Interlux barrier coat?

Osmosis is caused by a chemical reaction between water and unreacted substances remaining in the manufactured hull. Water breaches the exterior gelcoat and reacts with the chemical components creating acidic substances. These substances create pressure behind the gelcoat which causes blisters and eventually cracking.

When to apply interprotect 2000E to bare wood?

Remove sanding residue with a brush, vacuum or by blowing off with a clean air line. Within 1 hour of preparing the surface, apply a coat of Interprotect 2000E thinned 15 -20% with the correct thinner. Apply 4 -5 additional coats of Interprotect 2000E. BARE WOOD Sand with 80 -180 grade (grit) paper.

Where can I buy Interlux osmosis gelcoat?

It’s formulated with Microplates® that creates an overlapping water barrier. It’s also great for repairing gelcoat that has been damaged by osmotic blistering. There are many stores that sell Interlux products throughout the United States. Find a retailer that’s near you.