What are the switches on back of Primo water dispenser?

CONVENIENCE SWITCHES – On/off switches for heating, cooling, nightlight and self-sanitization are located on the back of the dispenser. SELF-SANITIZATION LIGHT – Flashes green when sanitizing. COOLING LIGHT – Flashes blue when water is cooling. Light turns off when water is fully chilled.

Why is my Primo water dispenser red light blinking but tank is full?

A flashing red function light alerts you when your bottle is empty. Replace the bottle as soon as possible. CAUTION: Do not dispense hot, cool or cold water if the red light is flashing as you could empty the tanks and cause the dispenser to overheat. 1.

Why is my primo dispenser not cooling?

Unplug the unit. After a few minutes, plug the unit back in, turn the switches back on and give it one hour and recheck the water temperature. If this does not correct the issue, please call our Customer Service Center.

How do you set the temperature on a Primo water dispenser?

How to Set the Temperature on a Primo Water Dispenser

1. Move the Primo water dispenser away from the wall, being careful not to tip or spill the water bottle.
2. Locate the flat, brass-colored screw on the back of the water dispenser.
3. Turn the screw slightly clockwise for colder water or counterclockwise for warmer water.

Can you use an extension cord with a water cooler?

Never use an extension cord to provide power to the cooler. If the electrical receptacle is not convenient to the location of the cooler, hire a qualified electrician to install a properly grounded outlet within reach of the power cord supplied with the cooler.

Why is my Primo water dispenser beeping?

If an air seal is not properly positioned, then the reservoir will not be able to fill with water. This would cause LED lights on the system to begin flashing. An audible “chirping” sound will be present as well. There is a simple solution to this issue: Secure the hoses and the seal on the bottle!

How do I fix my water dispenser not cooling?

This is very easy to do: First, remove a few cups of water from your machine, then completely unplug your water cooler from the mains. We then suggest leaving your machine for 24 hours before switching it on again. After 24 hours, plug it back in and wait 6 hours for the water to adjust to a cooler temperature.

Why is my water dispenser not cold?

Water Cooler not dispensing hot/cold water (It’s room temperature) Option 1 – Check that your water cooler is plugged in at the wall socket and that the mains power is turned on (a surprisingly common cause). Option 2 – Check that the switches on the back of the cooler are turned on and illuminated.

Do you have to plug in a water cooler?

Remember that water coolers or heaters need to be plugged in, so they will need to be positioned near an outlet.

What do you need to know about the Primo Water Cooler?

Power Supply Water Dispenser Primo Water User Manual. Bottled water. Operating Indicators – Circular lights mean dispenser is heating or PrimoWater .com to find Primo Water at a store near you. . replacement of parts, which prove defective under normal use and service and which Vendor shall determine in.

What does it mean to have a Primo Water Dispenser?

That means all kinds of lives—busy, relaxed or somewhere in between. Whether you’re a traveler, a homebody, a parent or a pet, Primo has a dispenser that’s just for you. Water we up to?

What happens when you replace a Primo water bottle?

REPLACING THE BOTTLE When your bottle is empty, the empty bottle light will flash. To prevent freeze-up or over-heating, the dispenser will not heat or cool water when the bottle light is flashing. Replace the bottle as soon as possible to re-enable cooling and heating. Open dispenser cabinet door and slide empty bottle out of cabinet.

How often should I sanitize my Primo Water Dispenser?

Primo recommends that you use the instructions below to dissolve mineral deposits, sanitize, and deodorize your dispenser every 3-4 months. Time Required: 30 minutes Need: (2) tablespoon regular bleach or (2) cups of distilled white vinegar, (1) Empty 5 gallon bottle, (1) 2-gallon bucket and a Philips head screwdriver.